Opens in a new tab

Asphalt Milling Contractors

Get a Free Estimate

If you’re looking for asphalt milling contractors in Athens, GA, you’re probably planning to resurface a lot or driveway and need the old pavement taken down first. Milling grinds the top of worn asphalt off to a set depth. That keeps the new surface from sitting too high at curbs, drains, and doorways, and leaves a rough, clean face for the new asphalt to bond to.

IB Paving is a locally owned company based in Athens, and we mill and pave lots, drives, and private roads across Northeast Georgia. Because we do both, one crew handles the grinding and the new surface.

Why Choose IB Paving as Your Asphalt Milling Contractors

  • Depth Set to Your Site: We mill only as deep as the job needs, so your sound base stays in place.
  • Milling and Paving Together: One team grinds and paves, so there’s no wait between the two steps.
  • 30+ Years of Experience: Our owner has been paving for more than 30 years and knows where heights matter most, like doorways, garage floors, and drain grates.
  • Locally Owned and Operated: You work with a team based in Athens.

Our Asphalt Milling Services

  • Full-Lot Milling: We grind the whole surface before a new overlay goes down.
  • Edge and Transition Milling: We mill along curbs and gutters so water still flows to the drains.
  • Doorway and Garage Milling: We take the surface down near entries so the new layer stays flush.
  • Spot Milling: We grind out rough areas and old patches before paving over them.
  • Drive Lane Milling: We level rutted wheel paths where traffic has pushed the asphalt out of shape.

Most milling leads into an asphalt overlay. Together, the two steps give you a new surface without digging out the base.

New asphalt parking lot beside milled pavement at a brick building

Why Mill Before Resurfacing

Paving over old asphalt without milling raises the surface every time. After a layer or two, the pavement builds up at the curbs until water has nowhere to go, and doors and garage floors end up lower than the pavement beside them.

Milling solves the height problem first. It also removes the cracked, oxidized top layer, the part sun and air have dried out and made brittle, so the new surface doesn’t sit on it. The rough texture left behind gives new asphalt a strong grip.

Milling won’t fix a weak base. Where the base has failed, we combine milling with full-depth patching before paving, so the overlay goes onto a surface that’s solid everywhere.

Asphalt Milling Services for Lots, Drives and Roads

Busy commercial lots show the clearest need. Years of traffic leave ruts in the drive lanes and buildup along the curbs. We mill those areas, then pave a fresh surface over the lot. If you’re planning a bigger project, see our parking lot paving work.

Driveways usually need milling at just two spots, the garage and the apron. A thin grind at each lets the new layer meet both cleanly.

Private roads need it where the crown has worn flat or the edges have built up. We grind those areas so the new surface sheds water again.

Hiring asphalt milling contractors who also pave means one crew handles both steps. There’s no gap between grinding and paving, so your lot reopens sooner.

How We Mill Asphalt

  1. Survey the Site: We mark the curbs, drains, and doorways where heights matter.
  2. Set the Depth: We decide how much to remove in each area.
  3. Mill: The milling machine grinds the asphalt and loads the millings into a truck.
  4. Sweep: We clear dust and loose material off the milled surface so the new layer bonds.
  5. Repair Weak Spots: Any soft base found under the old asphalt gets rebuilt.
  6. Pave: We tack the surface and lay new hot asphalt.
Paver hopper loaded with asphalt at a milled entrance

Asphalt Milling FAQ

How deep do you mill?

It depends on the condition of the old surface and how thick the new layer will be. We set the depth area by area.

Can I drive on milled asphalt?

Yes, for a short time. The surface is rough and the edges are uneven, so we pave soon after milling.

What happens to the old asphalt?

Millings can be recycled into new pavement or used on gravel roads and drives. Some homeowners use them for a recycled asphalt driveway.

Do you mill driveways?

Yes. Homeowners call us when a new layer would sit above the garage floor. A thin grind at the garage and the apron fixes that.

Is milling loud?

Yes, the machine is loud while it runs. We work during daytime hours and tell you ahead of time how long it will take.

Ready to Get Started?

Call 706-710-4222 or fill out the form for a free, no-obligation estimate.

Free Estimate
Complete the form below for a free, no-obligation estimate.

Our Past Work

Free Estimate
Complete the form below for a free, no-obligation estimate.